一区二区激情视频,www.少妇熟女.com,欧美99久久久,久久黄色电影好爽

Welcome to Wuhan Micro Power Auto Parts Co.,Ltd.

CATEGORY

Applicable Cummins series Applicable Hino series Applicable Isuzu series Applicable Komatsu series Applicable Mitsubishi series Applicable Nissan series Applicable Deutz series Applicable Benz series Applicable Daewoo series Applicable Man Series Applicable Carter series
NEWS >> MORE
Wuhan Micro Power Auto Parts Co.,Ltd.
Introduction to the steps of cleverly installing piston rings
Quality inspection problems of automobile piston rings
The meaning of piston ring work
Classification of piston rings
CONTACT US >> MORE
Wuhan Micro Power Auto Parts Co.,Ltd.

Contact:Manager Luo

Tel:0031-63300-3808

Email:luoljj@126.com

Address:No. 30, Yongjia Mountain, Lucheng Street, Xinzhou District, Wuhan City, Hubei Province

NEWSPosition:Home>News

Introduction to the steps of cleverly installing piston rings

Author: PubTime:2020-05-13

The main points of piston ring installation are as follows:    

1. Press-fit connecting rod copper sleeve. When installing the connecting rod copper sleeve, use a press as much as possible, or with the help of a vise, do not use a hammer to hit hard; the oil hole or oil groove on the copper sleeve and the oil hole on the connecting rod should be aligned to ensure its lubrication; After the sleeve is pressed in, the distance between the two ends of the connecting rod end face should be equal.   

2. Assemble the piston ring and connecting rod. When assembling the piston ring and connecting rod, pay attention to their relative position and direction. If the big end of the connecting rod is a flat cut, the vortex groove on the top of the piston should be on the same side as the big end of the connecting rod; if the big end of the connecting rod is an oblique cut, the vortex groove on the top of the piston should be on the same side as the upper end of the oblique cut. The top end of the piston should be pointed toward the fuel injection pump.    

Three, cleverly installed piston pin. The piston pin and the pin hole are interference fit. During installation, the piston should be evenly heated to 90℃~100℃ in water or oil. After taking it out, put the pull rod in the appropriate position between the piston pin seat holes, and then install the piston pin coated with organic oil in the predetermined direction. Into the piston pin hole and the connecting rod copper sleeve. At the same time, push the piston pin while moving the connecting rod. Use your thumb or palm to slap into the pin hole and the copper sleeve of the connecting rod head, and move in it, indicating that the tightness of the two is suitable. To make the distance between the end face of the piston pin and the two piston pin retaining rings equal, install the retaining rings.    Fourth, the installation of the piston ring. When installing piston rings, pay attention to the position and sequence of the rings. A gas ring on the piston is generally a chrome-plated ring. The second and third rings are mostly torsion rings, but there are also conical rings. If it is an inner cut ring, the cut should face downward; if it is a tapered ring, the side or taper angle engraved with the word "up" should face upward. The piston ring should not be stuck in the groove; the opening of a gas ring should not directly face the piston pin hole and the vortex groove on the piston top; the opening positions of adjacent rings should be staggered by 90 to 120 degrees to prevent gas leakage in the cylinder , To facilitate sealing. After the piston ring is installed, check its opening clearance (end clearance) and side clearance. If the opening gap is too large, it is easy to cause air leakage. If the gap is too small, it will cause jamming; the edge gap refers to the gap between the piston ring and the ring groove in height, which enables the ring to move freely in the ring groove without jamming. This gap should not be too large, otherwise, when the piston moves up and down in the cylinder, the gas ring will pump oil, and the lubricating oil will enter the combustion chamber, accelerating the consumption of lubricating oil and causing serious carbon deposits.    

5. Install the connecting rod group. When the connecting rod is assembled into the cylinder, when installing the connecting rod cover, pay attention to the matching mark on the big end of the connecting rod. At the same time, use a torque wrench to tighten the bolts in 2~3 times according to the specified torque. Rotate the crankshaft without jamming, and then install the lock. Tighten the wire or fuse.

亚洲日本母乳中文字幕| 久x性色AV粉嫩av性xz| 99视频欧美三区| 日韩欧美不卡大屁股被插| 久久69国产一区二区蜜臀| 国产草草| 欧美综合日韩综合国产综合在线| 淫色网国产图片| 精品国产流白浆| 国产久久日麻豆| 涩涩热综合资源网| 日韩影视一区二区中文| 从哪里看艹逼逼| 国产熟女熟女| avzx久久久| 2027日本精品国产| 99国产黄片| 丝袜少妇被操| 精品一二一| A级毛片网址| 国产熟女乱| 台湾中文娱乐二区| 美女久久精品视频| 欧美日韩成人高清网址| 亚洲1区a区| 伊人成伊人网| 麻豆一区二区在线观看2| 麻豆三级视频在线| 99成人黄色网址| 嗯嗯,久久嗯| 美女想被插91视频| 亚洲字幕中文日本精品| 久久伦理一区之区| 国产综合一区99| 日本加勒比福利视频| 青青草免费在线视频香蕉| 久婷色综合| 亚洲欧美日韩另类| 国产粉嫩不卡| 日本极品一区二区不卡| 婷婷 日韩 在线 一区 舔 湿|